Monthly Archives: June 2014

Aqua Products Aquabot Inground Automatic Swimming Pool Robotic Cleaner

Aqua Products Aquabot Inground Automatic Swimming Pool Robotic Cleaner


Aquabot robotic automatic inground pool cleaner. Every aqua products’ robotic cleaner comes equipped with a computerized microprocessor and sensors that allow it to adjust to any shape, size and type of pool. This brain allows the aquabots pool cleaner to brush, scrub, vacuum and filter the full length and breath of the pool. Such advanced technology allow aquabots to climb the walls and most steps, work around ladders and raised drains, and go into and around corners. Aquabots reverse themselves as they work up the walls to the water line, slightly changing the angle before descending the walls to clean new areas. Every seventh time aquabots climb the wall, it travels along the inside lip of the pool below the coping giving the waterline and tile above it scrubbing attention. Aqua products’ technicians install the microprocessor in every unit by hand.

Every cleaner is tested and inspected to maintain the highest level of quality. Before installation, the microprocessor is pre programmed so that it will adjust to virtually every pool and pool environment. When aquabots encounter an obstacle, a raised drain, ladder, wall or corner, they instantly adjust and continue to clean.


Built in filtration system takes all the work out of cleaning your pool. No more dragging out and connecting vac hoses — just plug in, drop in, and let it go to work! No need for supervision — the aquabot pool vacuum is pre-programmed for efficient, thorough cleaning of any size, shape, or type pool without getting hung up on ladders or steps.

High-powered suction removes the finest particles of algae, bacteria, dirt debris, sand and hair from the pool’s floors, steps, walls, and even the waterline! As it cleans, aquabot automatic pool cleaner equalizes the water temperature and chemical distribution, reducing heat and chemical costs. Water is filtered through the aquabot at a rate of 4,000 gallons per hour, while it cleans 3,500 sq.

Not for use at a commercial facility. The aquabot safely operates off 24 volts at a cost of about only 25 cents a day. The original robotic pool cleaner. With all the features to make cleaning your pool a breeze! No installation or assembly required.

Built-in filtration system — completely independent of the main pool filter… No messy hoses to deal with! Cleans any size, shape and type of in-ground pool. Pre-programmed for efficient, thorough cleaning of your pool. Climbs and cleans pool sidewalls.

Vacuums all types of debris. Lightweight — operates on only 24 volts. Walks up and scrubs most pool steps.

Quantity of water filtered = 4000 gals. Cleaning coverage = 3500 sq. Electrical cord length = 51 ft. Unit weight = 17 lbs.

Operating cost = less than 25 cents per day. Electrical plug = 110v/60hz or 230v/50hz. Filtration-mircron rating = self contained 2 micron. Scrubbing ability = heavy duty. X 17.5 in x 19.5 in. Aquabot gives you more time to enjoy your pool. Just plug it in, drop it into your pool and turn it on… The aquabot will do the rest! Is pre-programmed to scrub, vacuum and filter dirt and debris from pool bottoms, walls, waterlines and steps… The aquabot cleans all sizes, shapes and types of in-ground swimming pools.

Has its own special filtration pump and bag located inside its body and operates completely independent of your main pool filter, eliminating the need for messy, bulky hoses. Engineered for reliable worry-free operation. The aquabot cannont become stuck on stairs or ladders or become tangled in hoses as with other pool cleaners. Just take the aquabot out of the box and put it in your pool…

Cut your summer pool bills in half! The aquabot drastically reduces the frequency of wasteful backwashing, saving thousands of gallons of water per year and reducing your chemical consumption by as much as 30%. With the aquabot at work in your pool, you can even decrease the running time of your pool’s filtration system by as much as 60%.

The aquabot has front and rear scrubbing brushes which loosen and remove heavy dirt and fine particles to be vacuumed and trapped in the filter bag. The aquabot has excptionally high suction power, enabling it to vacuum up all types of dirt and debris from your pool. The aquabot will clean and purify thousands of gallons of water per hour. The aquabot is equipped with an oversized, re-usable filter bag that has a large capacity to hold leaves and other debris.

The filter bag can easily be removed for periodic cleaning. Removes algae growth and bacteria. The aquabot will scrub, vacuum and filter out all types of debris, including algae and other small particles.

As a result of the aquabot’s heavy-duty pumping action, the pool’s bottom water is circulated and forced to the surface, raising the overall water temperature and creating a more equal distribution of chemicals that would normally settle to the floor of the pool. Operating the aquabot is as simple as dropping it into your pool and plugging it in. It does the rest itself. The aquabot is safe and easy to use, operating only only 24 volts (the equivelant of three radio batteries) and costing less than about 25 cents a day to run. The aquabot requires little or no maintenance.

The aqubot is constructed of corrosion-proof materials and has fewer than 10 moving parts. These rates apply to the lower 48 states only. Save on pool supplies now delivers on saturdays for no additional charge.


If the combined weight of your order is 500 lbs. We strive to provide you with high quality products.


The item “Aqua Products Aquabot Inground Automatic Swimming Pool Robotic Cleaner” is in sale since Thursday, August 15, 2013. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Cleaners”. The seller is “saveonpoolsupplies” and is located in United States.

This item can only be shipped to United States.

Recent searches

  • intex pool skimmer

Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E

Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E


Read the entire listing prior to purchasing this item. Brand new intex deluxe maintenance kit. The ultimate in pool maintenance kits, the intex deluxe pool maintenance kit is perfect for keeping intex pools clean and fresh for swim time. This kit includes a 110 telescoping aluminum shaft for use with 18′ diameter pools and above. The kit also includes a vacuum that sucks debris off the pool floor and through the filter requires an intex filter pump with a minimum flow rate of 1000 gph or greater and can attach to the outlet connector in the pool with the included 24′ 7 hose. The telescoping aluminum shaft can be used with the following included attachments: vacuum head, durable and deep mesh skimmer net, and wall brush attachment. This kit has every tool you need to keep your intex pool sparkling clean! This maintenance kit is designed for use with intex brand swimming pools with an intex 1000 gph filter pump. Intex brand pools say “intex” in large white letters on the pool wall. If your pool does not say “intex” on the pool wall, it is not an intex brand pool. We do not guarantee fitment with any other brand of pool or any non pool application. Pool application and open the packaging to “test” your application, the kit is not returnable. Attaches to a filter pump for automatic vacuuming.

Requires an intex filter pump with a minimum flow rate of 1000 gallons per hour. 110 telescoping aluminum shaft for use with 18′ diameter pools and above. Vacuum head, durable and deep mesh skimmer net, and wall brush attachment. Durable polypropylene plastic is not affected by pool chemicals. 24 foot 7 inch long hose included.
Intex deluxe maintenance kit – model 28003e. When requesting a return please follow these guidelines. Merchandise must be in its original unopened packaging with all parts and accessories. Additional charges may apply for missing or damaged parts, accessories, manuals, etc.

Air beds are a personal item and are not returnable for hygienic reasons if opened. All of the products we sell are brand new, factory direct and factory sealed.


We do not sell, used, opened, refurbished or factory second products. Item will be replaced one time with a new identical item only. Our customer support is available m-f 9-5 cst.
The item “Intex Deluxe Maintenance Swimming Pool Cleaning Kit with Vacuum & Pole 28003E” is in sale since Tuesday, May 27, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Cleaners”. The seller is “windycitysuperstore” and is located in Round Lake, Illinois. This item can only be shipped to United States.

  • Brand: Intex
  • Model: Deluxe Maintenance Kit
  • MPN: 28003E
  • Pool Type: Intex Above Ground
  • Intex Pump Requirement: Intex 1000 GPH Filter Pump or Greater
  • UPC: 0-78257-31654-0

Recent searches

  • kit intex manitenance 28003/e
  • Part Number: 58959E / 28003E

Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING

Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING


Pentair ic-40 salt cell # 520555. Brand new in the box genuine oem pentair cell. The lower 48 states only.

This cell is for both replacement and new installation. (if new installation, you will need to have the power center #520556) which we also have listed separately or as a set with a cell. 3.04 (power center not included). These are excellent chlorine generators for pools up to 40,000 gallons. Now, crystal clear, safe water is automatic.


Electrolytic chlorine generation is the easiest, most effective and convenient way to keep pool water sparkling clean. The intellichlort chlorine generator uses common table salt to produce all the chlorine your pool needs, right in your pool – safely, effectively, and automatically. Same sanitation performance as manual chlorine addition without the drawbacks. No more odor, stinging eyes, irritated skin and bleached out swimsuits.

The intellichlor chlorine generator is engineered to stand up to the toughest pool conditions and provide years of dependable performance. Titanium electrode cell blades are coated with ruthenium oxide and are rated for more than 10,000 hours of operation – five years of reliable chlorine output under normal operating conditions. Control electronics are isolated in the cell, away from high heat components, for longer cell life. Totally waterproofed electronics for maximum reliability. Three led salt level indicators. Five sanitizer output levels with two-button control.
Oem pentair intellichlor ic40 salt cell. This is the newest version 3.04 cell from pentair.

Please observe the direction of the flow arrow when replacing your old cell as the display has been changed on the newer genuine pentair cells. Please let us try and resolve any issues you may have before leaving negative feedback.

The item “Pentair Intellichlor IC-40 Salt Cell FREE SHIPPING” is in sale since Monday, April 14, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Cleaners”. The seller is “y-notpoolparts” and is located in Phoenix, Arizona. This item can only be shipped TR.

  • Brand: Pentair
  • Model: IC-40 Salt Cell

Recent searches

  • y-notpoolparts
  • phoenix y-notpoolparts
  • y-notpoolparts phoenix 602 5323939
  • how to wire a pentair intellichlor ic 40 to an intelliflo variable
  • y-notpoolparts phoenix
  • y-notpoolparts phoenix az
  • y-notpoolparts pool business

Smartpool KLEEN MACHINE (Nitro) Robotic Automatic Pool Cleaner Vacuum

Smartpool KLEEN MACHINE (Nitro) Robotic Automatic Pool Cleaner Vacuum


Smartpool KLEEN MACHINE (Nitro) Robotic Automatic Pool Cleaner Vacuum


The kleen-machine is a sophisticated “floor specific” robotic pool cleaner that will work in any aboveground or inground pool! Its unique design was engineered to vacuum and brush pool floors of any surface type (vinyl, concrete, fiberglass) fast and efficiently. Unlike other heavy and clumsy robotic cleaners, this cleaner features a patented lightweight design that makes it easy to use. In 2010, pg&e determined that the kleen-machine is eco-friendly energy efficient – at least 88% more energy-efficient than other types of automatic pool cleaners.

Kleen-machine’s extra-large filtering bag allows the pool owner longer periods of time between emptying. The patented location of the robot’s intake ports gets into corners, ridges and angles to clean the entire pool floor where the dirt is. The pool trends kleen machine is manufactured by smart pool and is the exact same cleaner as the #1 leading smart pool nitro! Kleen machine robotic pool cleaner for above-ground, on-ground, & in-ground pools.

Lightweight design weighs only 9 lbs. Rapid drain system keeps debris in filter bag while clean water flows back into pool. Easy plug-in installation and operation (no tools required). Applicable for any size or shape pool up to 20ftx40 ft in size, including pools with a deep end. Vacuums and scrubs entire pool floor.

Systematically cleans your pool in less than 2 hours. Lightweight and easy to lift. Operates on all pool surface types: vinyl, concrete and fiberglass. Operates independently from your pool’s filter system. Automatic shut-off – robot shuts off at the end of its cleaning cycle. Completely safe – etl listed to ul standards. Power supply input voltage: 115 vac 60 hz. Power supply output voltage: 24 v dc. Filtering media: fine porosity filter bag. Dimensions: 13.5 l x 15.3 w x 17.5 h. If the unit you receive is defective out of the box (which is highly unlikely), we will quickly replace it with another after we receive the defective unit back. We are an actual swimming pool supply dealer with 3 stores located outside of pittsburgh, pa.

Have any questions about this product? Please ask and we can answer!

The item “Smartpool KLEEN MACHINE (Nitro) Robotic Automatic Pool Cleaner Vacuum” is in sale since Wednesday, February 26, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Cleaners”. The seller is “poolstuffxpress” and is located in North Versailles, Pennsylvania. This item can only be shipped TR.

  • Brand: Smartpool
  • Model: Kleen Machine
  • MPN: PTKM100
  • Pool Type: All
  • Pool Cleaner Type: Robotic

Recent searches

  • smartpool 2014 catalog

Vinyl Works A-Frame Ladder with Slide Lock System for Aboveground Swimming Pools

Vinyl Works A-Frame Ladder with Slide Lock System for Aboveground Swimming Pools


Vinyl Works A-Frame Ladder with Slide Lock System for Aboveground Swimming Pools


Product for the poolsupplies lineup. Vinyl works a-frame ladder with slide lock system for aboveground swimming pools.
(when you call please reference source code l14ydpg). Our model sla slide-lock a-frame ladder is designed for strength and ease of entry-exit of your pool. It is fully adjustable, on both sides, from a minimum of 48 inches to a maximum of 56 inches in height.

It is manufactured from maintenance free resin and complete stainless steel hardware for years of worry-free use. New anti-entrapment barrier to prevent swimming trough open treads of ladder. Double, extended handrails for easy climbing. When the pool is not in use, simply slide exterior portion up & lock. Full adjustable height – both sides of ladder.

Vinyl works canada manufactures this pool ladder to meet or exceed nspi/boca/ansi requirements for above ground/on ground pool ladders. The model sla001 a-frame ladder is manufactured using maintenance free resins. The ladder is adjustable from 48″ to 54″ for proper installation requirements and. This a-frame ladder is designed for load bearing weight of 350 lbs/one person. This ladder features permanently embossed signage and verbiage specifying no diving/no jumping, do not swim through, around or behind.
Ladder and to secure ladder when not in use (all required signage). This a-frame ladder features a slide-lock design. The exterior ladder section can slide up and can be locked to form an additional entry barrier for greater security. The ladder features four treads on both sides and a top platform tread.

Treads measure 17¼” wide x 3½” deep. The tread rise measures 10¾ high. Platform measures 18½” wide x 11½” deep. All treads and top platform are anti-skid.
The ladder is supported on two base treads on both sides of the pool. Each base tread is pivotal and can be rotated to ensure a solid, level base for greater stability. The pivotal base tread is also designed as not to damage the pool liner. A double, extended handrail on both sides of the ladder assists both entry and exit of. The handrails are extended an addition 10 downward on both sides of the.

Ladder to facilitate climbing from all treads. The ladder is required to be secured directly to the pool structure for greater stability. Securing hardware and instructions are provided with each ladder. If a customer build a deck; the conversion kit can be used, the ladder separated and the. Customer is able to build both an in-pool ladder and a ground to deck ladder and use.

All the parts of the initial a-frame model. Vinyl works canada encourages customer inquiries – any questions, comments or concerns ? Our experienced staff can assist in walking you through the checkout process. If you do not want an item left at your doorstep, the best thing to do is leave a note on your door with instructions for the driver.

A copy of your invoice and order # should be included, and your return should be insured. A damage claim will be filed on your behalf and we will replace the item immediately once the claim is approved. Contact our customer service department and an immediate replacement order will be prepared for you. In certain cases, we may require pictures, and or a sample of the defective item.

These items cannot be returned to the merchant. Monday – sunday 6:00am – 9:00pm est.

The item “Vinyl Works A-Frame Ladder with Slide Lock System for Aboveground Swimming Pools” is in sale since Wednesday, April 25, 2012. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Other”. The seller is “poolsupplies” and is located in Tonawanda, New York. This item can only be shipped to United States.

  • Brand: Vinyl Works of Canada
  • Model: A-Frame w Slide Lock
  • MPN: SLA001
  • UPC: 694139333339

Confer 7200 Roll Guard Heavy Duty A Frame Aboveground Swimming Pool Ladder

Confer 7200 Roll Guard Heavy Duty A Frame Aboveground Swimming Pool Ladder



Confer roll guard 7200 a-frame safety ladder. Aesthetically pleasing contemporary design in beautiful warm gray color. Large 5 inch x 18 inch wide comfortreads. Curved side rails designed with strength in mind. Inner side rails include integrated side barriers to prevent entry behind the ladder. Easy assembly with minimal hardware. Adjusts to fit pools 48″ to 56″ tall. Lockable roll-guard barrier (lock included). Just fill side rails with water to prevent floating, no sand or bricks needed. Fits pool top seats up to 14 inches wide.

Will not work with intex or other soft-sided pools. These rates apply to the lower 48 states only. Save on pool supplies now delivers on saturdays for no additional charge. If the combined weight of your order is 500 lbs.

We strive to provide you with high quality products.The item “Confer 7200 Roll Guard Heavy Duty A Frame Aboveground Swimming Pool Ladder” is in sale since Monday, June 09, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Other”.

The seller is “saveonpoolsupplies” and is located in United States. This item can only be shipped to United States.

Affordable Pool Parts

Extreme Force 1.5 HP Single Speed Pump for Above Ground Swimming Pool w/Cord

Extreme Force 1.5 HP Single Speed Pump for Above Ground Swimming Pool w/Cord


Product for the poolsupplies lineup. Extreme force 1.5 hp single speed pump for above ground swimming pool w/cord.

(when you call please reference source code l14ydpg). This pump has been engineered for durability and quiet performance with economy in mind.

The mighty force of this pump makes it efficient and an economical choice. The extreme force pump features a 2-piece strainer cover with clear view port, large hair and lint basket.

Efficient, full-flow hydraulics produce more flow at equivalent horsepower, resulting in lower operating costs. This pump is designed for maximum performance and economy in an aboveground swimming pool pump. Threaded inlet and outlet port. Includes power cord and strainer basket.

Threads are in the inside and outside. Designed for above ground pools, only. Our experienced staff can assist in walking you through the checkout process. If you do not want an item left at your doorstep, the best thing to do is leave a note on your door with instructions for the driver. A copy of your invoice and order # should be included, and your return should be insured.

A damage claim will be filed on your behalf and we will replace the item immediately once the claim is approved. Contact our customer service department and an immediate replacement order will be prepared for you. In certain cases, we may require pictures, and or a sample of the defective item.

These items cannot be returned to the merchant. Monday – sunday 6:00am – 9:00pm est.

The item “Extreme Force 1.5 HP Single Speed Pump for Above Ground Swimming Pool w/Cord” is in sale since Wednesday, April 10, 2013. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Pumps”. The seller is “poolsupplies” and is located in Tonawanda, New York. This item can only be shipped to United States.

  • Model: Extreme Force
  • MPN: 72730
  • Pool Type: Above-Ground
  • Speed: Single-Speed
  • Horsepower: 1.5 HP
  • Voltage: 115V

Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber

Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber


Pressure side automatic pool cleaner. The polaris 280 is a pressure side pool cleaner designed for all in ground pools and runs off a booster pump and double jets.
Sweeping, scrubbing and vacuuming, the 280 collects debris in its high capacity filter bag. This cleaner connects to your dedicated pressure line and requires a booster pump for operation. This pressure side pool cleaner can hold small and large debris in its filter bag, keeping it from entering your filtration system and extending its lifetime. The double jets and booster pump provide fantastic vacuum power and faster cleaning. The polaris 280 is also available in a black max model to complement dark bottom pools. The 280 pressure side pool cleaner by polaris is the powerful and dependable choice for your in ground swimming pool.

Pressure side cleaner for in ground pools. Sweeps and scrubs the bottom and walls of any pool.

Works with all pool surface types. Requires a booster pump for operation. The polaris 280 comes with a high capacity filter bag that collects and holds both large and small debris, including leaves and pine needles that can be missed by other cleaners.

With a three-wheel design and double jets, the polaris 280 features a unique, reliable build that easily navigates its way across pool surfaces. Check owner’s manual for details.

Trusted by pool and spa owners since 2006. Poolsupplyworld has been serving customers as a pool and spa resource since 2006. We believe that prompt, courteous communication is one of our best qualities, and we’re always looking for new ways to make shopping with us an easier, more convenient experience. Customer service – you can reach us in one of three ways. Get help from one of our helpful support representatives at.

With one of our trained techs at. We carry over 50,000 products.

More than a pool store! We want to help you. We value building long term relationships. We want you to count on us. For any questions feel free to.


The item “Polaris 280 In Ground Pressure Side Automatic Pool Cleaner Sweep F5 Scrubber” is in sale since Monday, December 23, 2013. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Parts & Maintenance\Pool Cleaners”.
The seller is “poolsupplyworld” and is located in Sunny. This item can only be shipped TR.

  • Brand: Polaris
  • MPN: F5
  • Model: 280
  • Pool Type: In-ground
  • Pool Cleaner Type: Robotic

Affordable Pool Parts