This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. Note: Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly. Thank you for your cooperation. How to use 1. Locate the pump as close as possible to the pool. The pump suction line should not be smaller than the pressure line. All piping must be airtight 3. The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on. The weight of the piping should be supported independently and not carried by the pump. Fill the pump tank with water before starting. High suction lifts, or long suction lines, require additional time and reduce the performance of the pump. The water being pumped cools and lubricates the seal. After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water. The installation must be according to the normal power indicated on the label. The amperage must not at any time exceed the value indicated on the label It is recommended that you consult a state-registered electrician. Place the pump in a dry area with good ventilation. The ambient temperature must not exceed 40? The pumps are only suitable for counter-clockwise rotation when viewing from the pump end. Three phase motors can rotate in either direction. Interchanging any of the cables on a three-phase motor will reverse the rotation. Momentarily start, or bump the motor without water in the tank, to check the rotation of the pump shaft. Before disconnecting electrical connections, shut off electricity at its source. Newer work on pump without making certain the power is OFF. This appliance is not intended for use by persons, including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety Children should be supervised to ensure that they do not play with the appliance. Problem Description: 1, The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out. Causes: The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water Solution: When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water. Inlet and outlet joints wrapped around the raw material tape, beware of leaks. Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage 2, Pump motor trip Causes: 1, The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. 2, The pump prevents the inlet from entering the water and burns the motor 3, There is Water in The Pump Causes: Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal. 4, The Pump stop working suddenly Causes: Our company’s products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process, generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise, pump stop working. Solution: Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller. Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter. 1.5HP&2.0HP 110-240V Swimming Pool Pump. 2.5HP 110V Swimming Pool Pump. Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak. Suitable for pools up to 100,000 litres. Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min. Full Size Removable Strainer Basket. 100% Salt and Chlorine compatible. Full Commercial Duty – Designed to run 24/7. Works with In ground and Above Ground. Built-In Thermal Overload Protection. Ideal for Residential/Commercial Swimming Pools & Spa’s. 10 1/3HP Sand Filter. Sizable Capacity – This sand filter pump is housed in a one-piece 10-inch tank with a capacity of 42 pounds of sand that can filter above ground pools up to 10,000 gallons Dependable Performance – This filter keeps the sand height level to expose water to the maximum sand surface level possible for optimum filtration, consistent performance, and efficient backwashing Low Noise Design – This sand filter pump is designed and optimized for running with low noise, to make your work more comfortable and energy efficient Simple and Easy to Use – 4-way valve, 3-prong plug w/ electric cable, portable, quick start and simple operation, take less than 5 minutes to install Multi-Port Filter – Multi port provides for easy use and quick back-washing. Pump and filter are perfectly engineered to provide optimum flow rates that promotes clean water quality 5-Way multi port provides for easy use and quick backwashing High efficiency pump lowers system cost and ensures years of quiet operation Flow rate of 2400 Gallons Per Hour swimming pool pump works swiftly and efficiently Machine will protect users’s safety entirely with build-in automatic thermal overload protector Pump strainer basket is the largest in its class with an easy open, quick lock, transparent pump lid which mean less work and more swimming. Type : Pool Pump Dual voltage : 110-120V/220V-240V Power : 1100w. Ampere : 10A/5A Horsepower : 1.5 HP Speed : 3450 RPM Max. Flow : 6500 GPH Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius) Frequency : 60HZ Qmax : 410 L/min Hmax : 15.5 Meter Power Cord : 59. Internal Thread diameter : NPT 1.5″ External Thread diameter : G2.25″ Certification : CSA and ETL. Model : SPPE 250 Power : 1850W/2.5HP Voltage : 110V / 60Hz. Flow : 560 L/m IP55 INS CL. 50 C Amps : 6.8 Head : Max 19m / 62.34ft Capacitor : 25 F Inlet : 1.5″ Internal Outlet : 1.5″ Internal Pipe Compatibility : Fit 1.5 inch plumbing internally Noise Level. Thread diameter : G2.25. Weight : 10.2 kg / 22.5 lbs. Type : Pool Pump Dual voltage : 110-120V/220V-240V Power : 1500w. Ampere : 13.6A/6.8A Horsepower : 1.5 HP Speed : 3450 RPM Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius) Frequency : 60HZ Qmax : 430 L/min Hmax : 15.5 Meter Power Cord : 59. Swimming Pool Pump X 1. Sand Filter X 1 Pool Pump X 1 System Tray X 1 Set of Accessories X 1. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. We have Five warehouses located in CA, TX, NY, NJ & GA. Some products may be dispatched in more than one carton. If you have a problem with the product. We will require a picture of the damaged part for verification. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “viphomesupply” and is located in this country: US. This item can be shipped to United States.
- Size: 2.5HP 110V
- Features: Easy Assembly, Easy Installation, Noise Vibration Reduction, Portable, Rust Resistant
- Manufacturer Warranty: Lifetime
- Certification: UL Certification
- Qmax: 410 L/min
- Item Width: 9.6\
- Hmax: 15.5 Meter
- Installation: Universal Installation
- Voltage: 110-120V/220V-240V
- Horsepower: 1.5HP/2.5HP
- Item Length: 22.4\
- Item Height: 11.4\
- Amper: 10.8/5.4A
- Motor Shaft Material: Stainless Steel
- Suitable For: Above Ground Pools, Inflatable & Kid Pools, In Ground Pools
- Power Source: Corded
- Material: ABS, Copper, PVC, Stainless Steel
- Speed: Single-Speed
- Model: 1.5HP/2.5HP
- Max. Temp: 104 Degree Fahrenheit (40 Degree Celsius)
- Rated Power: 1.5HP/2.5HP
- Item Weight: 26lbs
- Pump Housing Material: PPGF30 + PC (anti-Oxident)
- Power: 1500 W
- RPM: 3450/min
- Power Cord: 59\
- Pool Type: In Ground &Above Ground
- Brand: HAPPY-SHOPPING01
- Warranty: Lifetime
- Color: Black
- Energy Star: A+++
- Set Includes: Swimming Pool Pump, Fittings, Full Instructions
- Frequency: 60HZ
- Max. Flow: 6500 GPH
- Type: Pool Pump
