2.0HP Swimming Pool Pump Motor Hayward w/Strainer Filter In/Above Ground 7080GPH. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.
Maintain a crystal clear and sparkling pool or spa that everybody loves with the new SPPE series self-priming 1850W electric swimming pool pump. How to use 1. Locate the pump as close as possible to the pool. The pump suction line should not be smaller than the pressure line. All piping must be airtight 3. The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on. The weight of the piping should be supported independently and not carried by the pump. Fill the pump tank with water before starting. High suction lifts, or long suction lines, require additional time and reduce the performance of the pump. The water being pumped cools and lubricates the seal. After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water. The installation must be according to the normal power indicated on the label. The amperage must not at any time exceed the value indicated on the label It is recommended that you consult a state-registered electrician. Place the pump in a dry area with good ventilation. The ambient temperature must not exceed 40? The pumps are only suitable for counter-clockwise rotation when viewing from the pump end. Three phase motors can rotate in either direction. Interchanging any of the cables on a three-phase motor will reverse the rotation. Momentarily start, or bump the motor without water in the tank, to check the rotation of the pump shaft. Before disconnecting electrical connections, shut off electricity at its source. Newer work on pump without making certain the power is OFF. This appliance is not intended for use by persons, including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety Children should be supervised to ensure that they do not play with the appliance. Voltage : 110V / 60Hz. Head : Max 19m / 62.34ft. Diameter of white connector : 48.5mm/54.5mm. Thread diameter : G2.25. Pipe Compatibility : Fit 1.5 inch plumbing internally. Weight : 10.2 kg / 22.5 lbs. 1 x SPPE250 Swimming Pool Pump. 1 x User’s Manual. Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak. Suitable for pools up to 100,000 litres. Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min. Full Size Removable Strainer Basket. 100% Salt and Chlorine compatible. Full Commercial Duty – Designed to run 24/7. Works with In ground and Above Ground. Built-In Thermal Overload Protection. Ideal for Residential/Commercial Swimming Pools & Spa’s. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Your product was damaged during transit. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back.
2HP Square Flange Pump Motor Century 56Y 230/115V (B2859). Refurbished w/ NEW Bearings, Capacitor & Windings Cleaner & Coated w/ Anti Seize Varnish. Bench TESTED for LOW AMP DRAW!! LOCAL INSTALL SERVICE AVAILABLE!!! Pentair: WhisperFlo, SuperFlo, Challenger. Sta-Rite: Max-E-Glas, Max-E Pro, Dura Glas, Dyna-Glas, Dyna Pro. Hayward: EcoStar, TriStar, MaxFlo XL.
1.0 HP 1.5 HP 2.0 HP Swimming Pool Water Pump In/Above Ground Motor Strainer. POWERFUL PUMP – Advanced engineering features an impeller that maximizes flow, minimizes noise, and self-primes in an energy-efficient manner; Pure stainless-steel motor provides not only an efficient, stable and safe running, but also long service life. STURDY CONSTRUCTION – The full body is constructed with commercial-grade reinforced thermoplastic that resists corrosion, ensuring superior strength and durability; Comply with ETL Safety Standard. DETAIL ORIENTED – The strainer is designed with an extra-large filter basket that is detachable for easy cleaning; See -through lid allows you a clear internal viewing; Built-in automatic thermal overload protector and airflow ventilation protects from overheating and damage; Note: Please fill the pump with water upon first use to prevent the motor from overheating. WIDE APPLICATIONS – Female thread and slip union connection for tool-free installation; Suitable for swimming pools, hot tubs, thermal springs, spas and irrigation system, but should not to be used with storable pools; Package includes: 1 x pool pump; 2 x black interface, 1 x manual. BEFORE YOU USE – Please do not turn on the pump without filling water! The pump must be filled with water before use, otherwise damage will be caused to the mechanical seal and impellers. Product Details of 1.0/1.5HP. Inner & Outer Thread Connector. Comes with 2 free 1.5 inch American standard internal thread connectors to help you set up with no hassle. Equipped with a drain plug on the bottom which is easy for drainage and avoids water accumulation during winter. Just revolve the stopper and pull it out. The strainer includes a large, easy-to-clean filter basket to filtrated dregs and keeps pool maintenance to a minimum. Product Details of 2.0 HP. Dual-Watt 12.5/6.25 Amp 2.0 HP self-priming pump delivers up to 113 GPM per minute, which meets your different demands. Voltage Change: The voltage can easily switch from 115V to 230V by setting the voltage regulating switch on the rear of the pump. Product Specifications of 1.0 HP. Pipe Size: 1-1/2 inch. Thread diameter: 1.5 inch. Max flow: 5280 GPH. Nozzle internal diameter: 48 mm/1.9 inch. Flow rate: 88 GPM. Nozzle External diameter: 58 mm/2.3 inch. Max head: 42.6 FT. Power Cord: Length of 78.7 inches, American three-pin plug. Product Specifications of 1.5 HP. Max flow: 5400 GPH. Flow rate: 90 GPM. Max head: 49.2 FT. Product Specifications of 2.0 HP. Voltage/frequency: 115V(In default) 230V. Ampere: 12.5A/6.25A. Max flow: 6800 GPH. Flow rate: 113 GPM. Max head: 55.7 FT. Power Cord: Length of 37.4 inches, American three-pin plug. Note: According to UL 1081 standard, the maximum power cord length should not exceed 3 feet. High efficiency & Low Noise & Heavy Duty Construction & Powerful Motor. Our swimming pool pump is made of a durable PP plastic shell and stainless motor that provides you with high-performance suction power and optimal flow. This pool pump runs very smoothly and is whisper quiet. Its airflow ventilation helps circulate water filtration and keeps your swimming pool clean and sanitary. Ideal for above-ground pools and spas in all types and sizes. Transparent Pump Lid – A see-through cover with cam-lock lid for quick inspection and tool-free service. Overloaded Protection – Prevents from overcurrent running that would cause overheating of the equipment. Huge Prefilter – The Strainer basket with internal ribs can filter out the debris and leaves that greatly reduce the frequency of cleaning and maintenance. Premium Material – Reinforced thermoplastic can resist the damage of chemicals in the swimming pool. Anodized Motor Body – Anti-corrosion anodized motor body prolongs its working life. Convenient Drain Device – Equipped with a drain plug on the bottom which is easy for drainage and avoids water accumulation during winter. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. As a company based in California, We devote ourselves to offering top notch products at the most reasonable prices. From 2015, we have grown into a global enteprise that severs customers from all over the world. And we are glad to have you joining this big family. All we want for you is a easier and merrier life. Infinite Blessings and Love to YOU!
Replacmant Pentair Whisperflo Almond 2 HP Pool Pump Motor ASB843A (hba220). Motor Total Horse Power: 2.9 HP. Motor True Horse Power: 2.0 HP.
Comments Off
Posted in pentair
Tagged almond, asb843a, hba220, motor, motornidec, pentair, pool, pump, whisperflo
2.0HP Swimming Pool Pump Motor Hayward w/Strainer Generic In/Above Ground. Always pay attention before use!! Before use, please adjust to the corresponding voltage for home use, and then fill the water pump with water before using it, otherwise the motor will be damaged. When adjusting the voltage, be sure to adjust after turning off the power. Otherwise the motor will be damaged. This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. Durable Corrosion -Stainless Steel 2.0 HP Shaft, the shaft is constructed with a reinforced thermoplastic body for longer life and durability. The sand filter is made of PPGF30 + PC, 100% drip proof, effective insulation and protection against pool chemicals, heat-resistant double-sized seal for long motor life. POOL PUMP-This self-priming heavy-duty pump delivers outstanding performance and reliability at a fantastic price and costs less than big name brands. The mighty force of this pump makes it efficient and an economical choice. UL Certified- This Swimming Pool Pump has a UL Certification to ensure recognized Standards for Safety. Type: Swimming Pool Pump. Motor Shaft Material: Stainless Steel. Pump Housing Material: PPGF30 + PC (anti-Oxident). Rated Power: 1500W/2.0HP. Inner/Outer coupling: 1-1/2”NPT G2-1/4′. 1 x Water Pump. 2 x 1-1 / 2”NPT Inner coupling. 2 x 48.5mm Inner coupling(free gift). This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “tuoke4″ and is located in this country: US. This item can be shipped to United States.
1.5 HP Swimming Pool Pump 110 Volt Outdoor Above Ground Strainer Motor Spa Water. Always pay attention before use!! Before use, please adjust to the corresponding voltage for home use, and then fill the water pump with water before using it, otherwise the motor will be damaged. When adjusting the voltage, be sure to adjust after turning off the power. Otherwise the motor will be damaged. This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. Durable Corrosion -Stainless Steel 1.5 HP Shaft, the shaft is constructed with a reinforced thermoplastic body for longer life and durability. The sand filter is made of PPGF30 + PC, 100% drip proof, effective insulation and protection against pool chemicals, heat-resistant double-sized seal for long motor life. POOL PUMP -This self-priming heavy-duty pump delivers outstanding performance and reliability at a fantastic price and costs less than big name brands. The mighty force of this pump makes it efficient and an economical choice. UL Certified – This Swimming Pool Pump has a UL Certification to ensure recognized Standards for Safety. Type: Swimming Pool Pump. Motor Shaft Material: Stainless Steel. Pump Housing Material: PPGF30 + PC (anti-Oxident). Rated Power: 1100W/1.5HP. Inner/Outer coupling: 1-1/2”NPT G2-1/4′. 1 x Water Pump. 2 x 1-1 / 2”NPT Inner coupling. 2 x 48.5mm Inner coupling(FREE GIFT). This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “wanbu-ew” and is located in this country: US. This item can be shipped to United States.
This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. Note: Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly. Thank you for your cooperation. How to use 1. Locate the pump as close as possible to the pool. The pump suction line should not be smaller than the pressure line. All piping must be airtight 3. The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on. The weight of the piping should be supported independently and not carried by the pump. Fill the pump tank with water before starting. High suction lifts, or long suction lines, require additional time and reduce the performance of the pump. The water being pumped cools and lubricates the seal. After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water. The installation must be according to the normal power indicated on the label. The amperage must not at any time exceed the value indicated on the label It is recommended that you consult a state-registered electrician. Place the pump in a dry area with good ventilation. The ambient temperature must not exceed 40? The pumps are only suitable for counter-clockwise rotation when viewing from the pump end. Three phase motors can rotate in either direction. Interchanging any of the cables on a three-phase motor will reverse the rotation. Momentarily start, or bump the motor without water in the tank, to check the rotation of the pump shaft. Before disconnecting electrical connections, shut off electricity at its source. Newer work on pump without making certain the power is OFF. This appliance is not intended for use by persons, including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety Children should be supervised to ensure that they do not play with the appliance. Problem Description: 1, The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out. Causes: The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water Solution: When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water. Inlet and outlet joints wrapped around the raw material tape, beware of leaks. Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage 2, Pump motor trip Causes: 1, The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. 2, The pump prevents the inlet from entering the water and burns the motor 3, There is Water in The Pump Causes: Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal. 4, The Pump stop working suddenly Causes: Our company’s products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process, generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise, pump stop working. Solution: Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller. Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter. 1.5HP&2.0HP 110-240V Swimming Pool Pump. 2.5HP 110V Swimming Pool Pump. Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak. Suitable for pools up to 100,000 litres. Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min. Full Size Removable Strainer Basket. 100% Salt and Chlorine compatible. Full Commercial Duty – Designed to run 24/7. Works with In ground and Above Ground. Built-In Thermal Overload Protection. Ideal for Residential/Commercial Swimming Pools & Spa’s. 10 1/3HP Sand Filter. Sizable Capacity – This sand filter pump is housed in a one-piece 10-inch tank with a capacity of 42 pounds of sand that can filter above ground pools up to 10,000 gallons Dependable Performance – This filter keeps the sand height level to expose water to the maximum sand surface level possible for optimum filtration, consistent performance, and efficient backwashing Low Noise Design – This sand filter pump is designed and optimized for running with low noise, to make your work more comfortable and energy efficient Simple and Easy to Use – 4-way valve, 3-prong plug w/ electric cable, portable, quick start and simple operation, take less than 5 minutes to install Multi-Port Filter – Multi port provides for easy use and quick back-washing. Pump and filter are perfectly engineered to provide optimum flow rates that promotes clean water quality 5-Way multi port provides for easy use and quick backwashing High efficiency pump lowers system cost and ensures years of quiet operation Flow rate of 2400 Gallons Per Hour swimming pool pump works swiftly and efficiently Machine will protect users’s safety entirely with build-in automatic thermal overload protector Pump strainer basket is the largest in its class with an easy open, quick lock, transparent pump lid which mean less work and more swimming. Type : Pool Pump Dual voltage : 110-120V/220V-240V Power : 1100w. Ampere : 10A/5A Horsepower : 1.5 HP Speed : 3450 RPM Max. Flow : 6500 GPH Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius) Frequency : 60HZ Qmax : 410 L/min Hmax : 15.5 Meter Power Cord : 59. Internal Thread diameter : NPT 1.5″ External Thread diameter : G2.25″ Certification : CSA and ETL. Model : SPPE 250 Power : 1850W/2.5HP Voltage : 110V / 60Hz. Flow : 560 L/m IP55 INS CL. 50 C Amps : 6.8 Head : Max 19m / 62.34ft Capacitor : 25 F Inlet : 1.5″ Internal Outlet : 1.5″ Internal Pipe Compatibility : Fit 1.5 inch plumbing internally Noise Level. Thread diameter : G2.25. Weight : 10.2 kg / 22.5 lbs. Type : Pool Pump Dual voltage : 110-120V/220V-240V Power : 1500w. Ampere : 13.6A/6.8A Horsepower : 1.5 HP Speed : 3450 RPM Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius) Frequency : 60HZ Qmax : 430 L/min Hmax : 15.5 Meter Power Cord : 59. Swimming Pool Pump X 1. Sand Filter X 1 Pool Pump X 1 System Tray X 1 Set of Accessories X 1. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. We have Five warehouses located in CA, TX, NY, NJ & GA. Some products may be dispatched in more than one carton. If you have a problem with the product. We will require a picture of the damaged part for verification. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “viphomesupply” and is located in this country: US. This item can be shipped to United States.
New Pentair 193742 new and ready to Go. We are in Asset Recovery and have all kinds of stuff. Small and Large Lots available. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “fxgroup0269″ and is located in this country: US. This item can be shipped to United States, Greenland, Bermuda, Saint Pierre and Miquelon, Canada, Mexico.
This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly. Thank you for your cooperation. 1, The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out. Causes: The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water. When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water. Inlet and outlet joints wrapped around the raw material tape, beware of leaks. Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage 2, Pump motor trip Causes: 1, The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. 2, The pump prevents the inlet from entering the water and burns the motor 3, There is Water in The Pump Causes: Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal. 4, The Pump stop working suddenly. Causes: Our company’s products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process, generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise, pump stop working. Solution: Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller. Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter. Temp : 104 Degree Fahrenheit (40 Degree Celsius). Certification : CSA and ETL. 1 x 2HP Dual voltage Swimming Pool Pump. This Swimming Pool Pump has a ETL/CSA Certification to ensure recognized Standards for Safety. High performance, energy saving motor with stainless steel shaft could stand wear and tear. Thermally protected motor for greater protection and longevity. Extra-large debris basket keeps pool maintenance to a minimum, letting you enjoy your pool more, while the clear cover lets you see exactly when the basket needs cleaning. Easy start up fill pump with water upon first use to prevent motor from overheating. Transparent cover helps to judge if the basket needs clean or not. Massive strainer basket holds extra capacity. Suggested Installation: 24″-26″ sand filter and above-ground pools. 304 grade stainless steel motor shaft, Powerful Pool Pump heavy-duty, high-performance motor with air-flow ventilation for quieter, cooler operation. Strainer basket to minimize how often you have to empty it. See-through strainer cover for a fast and easy check of the strainer. Easy-thread strainer housing ring makes cover removal extremely easy. Dependability with carborundum and graphite mechanical seals and components molded of corrosion-proof, reinforced thermoplastic. Convenient drain plug makes winter maintenance easy. High Efficiency Impeller maximize flow and reduce noise while the energy efficient motor with commercial-grade frame; Internal Inlet Fitting: 1.5″ NPT (fit for 1.5″ male threaded adapter). All items are dispatched from our warehouse in Azusa, CA. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps”. The seller is “viphomesupply” and is located in this country: US. This item can be shipped to United States.